Intel 965 ICH8 MTK flash ?

[philb]

Has anyone got a link for MTKflash which will work with the new Intel 965 chipset ? ICH8

I flashed my xbox previously using my Nforce 4 board. I want to update to the new firmware 3.2 on my samsung, but ive just changed motherboards.  I've tried the standard 1.83C MTKFlash and cant seem to get it to recognise the DVDROm from jmy Xbox 360, its showing in the bios

Cheers

Phil

[philb]

I guess there's non about at the moment, I tried hex editing MTK flash with the guide I found but so far its no different

Any help much appreciated

here's my device ID if its any help

Name   Intel(R) ICH8 4 port Serial ATA Storage Controller - 2820
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_2820&SUBSYS_B0021458&REV_02\3&13C0B0C5&0&FA
I/O Port   0x0000F000-0x0000F00F
I/O Port   0x0000FC00-0x0000FC0F
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 07/08/2004 01:17)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&227B4D2C&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 04/08/2004 03:59)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&227B4D2C&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 04/08/2004 03:59)
   
Name   Intel(R) ICH8 2 port Serial ATA Storage Controller - 2825
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_2825&SUBSYS_B0021458&REV_02\3&13C0B0C5&0&FD
I/O Port   0x0000D800-0x0000D807
I/O Port   0x0000DC00-0x0000DC03
I/O Port   0x0000E000-0x0000E007
I/O Port   0x0000E400-0x0000E403
I/O Port   0x0000E800-0x0000E80F
I/O Port   0x0000EC00-0x0000EC0F
IRQ Channel   IRQ 19
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 07/08/2004 01:17)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&20F4DC72&0&0
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 04/08/2004 03:59)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&20F4DC72&0&1
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 04/08/2004 03:59)


Cheers

Phil

[philb]

I've got it working !
mtkflash r /sata / m orig.bin to backup it up
mtkflash w /sata / m x33.bin to flash

[cgower]

hi did you edit the mtkflash or not if so could you give it to me or make a link for it
thanks
casey

[philb]

I tried editing which didnt seem to work, in the end i used the standard MTKflash 1.83c and the commands in my previous message.
Cheers.

I can send it if your still having problems

Phil

[BuckPeter]

Hi folks - An old thread i know

But can anyone confirm that I prep 101 v0.0.2 works with the ICH8 chipset.

thanks

[Gash]

Hi folks - An old thread i know

But can anyone confirm that I prep 101 v0.0.2 works with the ICH8 chipset.

thanks

I know your post is about a month old, but I successfully flashed a Samsung drive with iPrep booting off of the USB flash drive.  It was kind of strange because in the guide I used it said to select the VIA sata drive in the list, but since I didn't have a VIA chip onboard I just chose IDE Master (SATA was set to IDE in the Gigabyte BIOS) and it worked perfectly.