XboxHacker BBS
 
Home Help Search Login Register
*
Welcome, Guest. Please login or register.
Did you miss your activation email? 		June 18, 2013, 07:20:16 PM


Login with username, password and session length


XboxHacker BBS > Xbox 360 > Tech Support 360 (Moderators: SiliconIce, Arakon, Redline99) > is my xbox knackered?
Pages: 1
« previous next »
  Print  
Author Topic: is my xbox knackered?  (Read 1901 times)
mcding
Newbie
*
Posts: 7


View Profile
« on: September 24, 2006, 11:54:16 AM »
hi just doin the vcc trick i desloder the middle chip but i accidentally nocked off the little chip next to it is it posible to rescue my xbox it hasnt been flashed yet so i havent got original key please help somebody please Sad
Logged
jumba
Master Hacker
****
Posts: 167


View Profile
« Reply #1 on: September 24, 2006, 05:58:56 PM »
You did not specify which one u knocked off. But, assume the the vcc trick location is correct the components are as follows:-
1 c404 =104 (cap)
2 r408 = 0 ohm (vcc trick resistor)
3 r409 =22k 0hm (flash write pull-up)
If u restore the missing one then you should backup the f/w make sure you get a good unload to get your key. If u loose it then xbox become a wonderful door stop!  Backup to a number of different files as insurance.
Logged
mcding
Newbie
*
Posts: 7


View Profile
« Reply #2 on: September 24, 2006, 06:08:03 PM »
Quote from: jumba on September 24, 2006, 05:58:56 PM
You did not specify which one u knocked off. But, assume the the vcc trick location is correct the components are as follows:-
1 c404 =104 (cap)
2 r408 = 0 ohm (vcc trick resistor)
3 r409 =22k 0hm (flash write pull-up)
If u restore the missing one then you should backup the f/w make sure you get a good unload to get your key. If u loose it then xbox become a wonderful door stop!  Backup to a number of different files as insurance.
it is no 3 that i have pulled off if i get it resoldered should it be ok?
Logged
jumba
Master Hacker
****
Posts: 167


View Profile
« Reply #3 on: September 24, 2006, 07:02:07 PM »
yes if the pads are not damaged
Logged
SoCal
Master Hacker
****
Posts: 101


View Profile
« Reply #4 on: September 25, 2006, 09:15:24 AM »
Quote from: jumba on September 24, 2006, 07:02:07 PM
yes if the pads are not damaged

Even if the pads are damaged you can scrape the traces and solder to that or look for altenate points and use a regular 1/8 watt carbon resistor. Just solder leads from the board to the reststor.

But if the pads are good and the resistor is not then just buy a new replacement resistor.
Logged
loon
Master Hacker
****
Posts: 200


View Profile
« Reply #5 on: October 05, 2006, 04:40:21 PM »
Quote from: SoCal on September 25, 2006, 09:15:24 AM
Quote from: jumba on September 24, 2006, 07:02:07 PM
yes if the pads are not damaged

Even if the pads are damaged you can scrape the traces and solder to that or look for altenate points and use a regular 1/8 watt carbon resistor. Just solder leads from the board to the reststor.

But if the pads are good and the resistor is not then just buy a new replacement resistor.
does anyone know an alternative point as both my pads are damaged on the middle one/
Logged
Pages: 1
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.11 | SMF © 2006-2009, Simple Machines LLC

Valid XHTML 1.0! Valid CSS! Dilber MC Theme by HarzeM