|
senk
|
 |
« on: April 01, 2012, 08:16:13 AM » |
|
Hey dudes im new at this forum, i will explain my case:
-To facilitate and expedite the whole process of reading a NAND Falcon plate, which I did was read the first 2 megs of NAND, I create and then write it NANDXell LPT cable. until there, so good.
-I turn on the console, and well, I start the Xell, showing all the fuses, the CPU key and Key Reader, then i connect the network cable from console to PC, and all the NAND dumpeo twice and then compare. Everything OK, are accurate ...
-I'm going to AutoGG again, I open one and I MSAMPLE dumpers everything right, I give the Dash version 14719 (latest), I give to create image, then I give and I believe RawFlash in the stick, ready to be flashed via Xell.
-Turn on the console with the Xell, start the whole process of writing and I jump for two error messages: Seems bad block 0x280, status 0x00000210 and another in the 0x328 block.
-When I finish the whole process, I turn off the console and then turn on the Power button, and it is infinitely blinking yellow light, however if Xell boot with no problem. The question is why Xell runs and Dash not? Why xbox360 runs when it wants (1 of 100 times) :S
Sorry for my english...
Thanks!
|
|
|
|
« Last Edit: April 01, 2012, 08:29:06 AM by senk »
|
Logged
|
|
|
|
|
senk
|
|
« Reply #1 on: April 02, 2012, 10:37:50 AM » |
|
No answers?  UPPPP |
|
|
|
|
Logged
|
|
|
|
|
|
|
senk
|
|
« Reply #3 on: April 02, 2012, 03:40:17 PM » |
|
Dude, thanks for the answer! here i go:
I tried to did but nothing, i've a question: Can i delete the NAND and put another previous DASHBOARD at the latest version to upgrade to do the RGH?
Thanks again!
|
|
|
|
|
Logged
|
|
|
|
|
Arakon
|
|
« Reply #4 on: April 02, 2012, 11:26:48 PM » |
|
No. The LDV would not match.
|
|
|
|
|
Logged
|
I do NOT give support by email, PM, ICQ or whatever. Anyone annoying me that way will have his balls removed. With a rusty butterknife. Slowly. And I'll enjoy doing it.
|
|
|
|
senk
|
|
« Reply #5 on: April 03, 2012, 04:19:55 AM » |
|
Well...what can i do? I tried with Nknave answer but nothing...
thanks for the answers!
|
|
|
|
|
Logged
|
|
|
|
|
Xumpy
|
|
« Reply #6 on: April 03, 2012, 05:16:00 AM » |
|
Use XeBuildGUI here you can get all the info (cpu key, ldv values) directly from xell when you build your image.
Good luck
|
|
|
|
|
Logged
|
Once your mind is running, returning to its original state feels like standing still.
|
|
|
|
senk
|
|
« Reply #7 on: April 03, 2012, 06:07:50 AM » |
|
At least, with the latest version of Dashboard i can't use my chip...(now i know..) anyone know what can i do? or i have to wait for a patch? (for ex: the coming TEAM XECUTER patch)
Thanks again!
|
|
|
|
« Last Edit: April 03, 2012, 06:36:18 AM by senk »
|
Logged
|
|
|
|
|
Xumpy
|
|
« Reply #8 on: April 03, 2012, 06:44:45 AM » |
|
If you can run xell you can run any freeboot you like. There is nothing wrong with your version or your chip if xell runs.
It probably is just like arakon said your LDV value which you can only fix if you read the manuall!!
Regards
|
|
|
|
|
Logged
|
Once your mind is running, returning to its original state feels like standing still.
|
|
|
|
senk
|
|
« Reply #9 on: April 03, 2012, 07:39:34 AM » |
|
Hey! Badlocks are solved and my friend told me that i have to wait for that patch (xecuter)...because my chip can't run with that version..
Thanks!
|
|
|
|
|
Logged
|
|
|
|
|
ddxcb
|
|
« Reply #10 on: April 03, 2012, 05:09:19 PM » |
|
Hey! Badlocks are solved and my friend told me that i have to wait for that patch (xecuter)...because my chip can't run with that version..
Thanks!
Well bad blocks was the issue, as in the original post, two what patch, you can run the latest dash. |
|
|
|
|
Logged
|
I'm a ADD modder, got to mod or be bored xD
|
|
|
|
Xumpy
|
|
« Reply #11 on: April 04, 2012, 01:10:17 AM » |
|
Ok now I'm curious, bad blocks could indeed be a problem why freeboot would not boot but you can solve that by remapping the bad blocks...
And if you allready done that and freeboot boots why do you still need a patch for your chip??
Regards
Xump
|
|
|
|
|
Logged
|
Once your mind is running, returning to its original state feels like standing still.
|
|
|
|
senk
|
|
« Reply #12 on: April 04, 2012, 07:41:36 AM » |
|
Ok now I'm curious, bad blocks could indeed be a problem why freeboot would not boot but you can solve that by remapping the bad blocks...
And if you allready done that and freeboot boots why do you still need a patch for your chip??
Regards
Xump
Hey dude, because my chip can't rule with that version of Dashboard (friend said that). Regards |
|
|
|
|
Logged
|
|
|
|
|
Xumpy
|
|
« Reply #13 on: April 04, 2012, 08:16:29 AM » |
|
But you can boot xell???
Haha, really the chip is just to bypass CB. If the console can boot xell then it should be able to boot freeboot no problem.
The way xell works (for newbies to understand):
1BL => CB => Glitch validation of CD => Custom Zero paired CD => Xell
The way freeboot works:
1BL => CB => Glitch validation of CD => Custom CD => Freeboot
The zero paired image can boot without LDV values correct (that's cause it's meant to retrieve the fuse values).
But to boot freeboot you need your correct LDV values (you retrieved from xell)
The chip is only there to to glitch the validation of CD in CB so we can load are own CD.
So now you see, no matter what your friend says. The chip is only there to glitch the CD validation. Everything afterwards is pure software.
Hope this helps,
Regards
|
|
|
|
|
Logged
|
Once your mind is running, returning to its original state feels like standing still.
|
|
|
|
Dilber MC Theme by HarzeM