|
Pacote-san
|
 |
« Reply #40 on: August 02, 2011, 08:01:35 PM » |
|
Here a tutz for the italian brothers (you can always try to google translate it if you like)... http://goo.gl/H9LJ8Thanks raiden Tomorrow morning will get the right bit and start drilling  |
|
|
|
|
Logged
|
|
|
|
|
|
alanyoung
Newbie
Posts: 7
|
|
« Reply #42 on: August 02, 2011, 08:32:34 PM » |
|
Our aim is to cut or touch with WP?
|
|
|
|
|
Logged
|
|
|
|
|
99belle99
|
|
« Reply #43 on: August 02, 2011, 08:52:49 PM » |
|
Can't wait to try this!
Buying the parts tomorrow or later today depending on the way you look at it, as it 2.50am in the morning.
I studied the video and he did not drill directly in the centre of the three reference points.
I'm still a bit confused about the cutting of the trace and using the 10-15 ohms resister(Like when do u do that part)
|
|
|
|
|
Logged
|
|
|
|
|
raidenxtribe
|
|
« Reply #44 on: August 02, 2011, 08:55:11 PM » |
|
Our aim is to cut or touch with WP?
Cut AND touch ! |
|
|
|
|
Logged
|
|
|
|
|
Pacote-san
|
|
« Reply #45 on: August 02, 2011, 09:15:05 PM » |
|
Just did my first Thanks again geremias   |
|
|
|
|
Logged
|
|
|
|
|
Pacote-san
|
|
« Reply #46 on: August 02, 2011, 09:18:40 PM » |
|
BTW locked again and tried to unlock with lighter, tried a few times withou success
Just touched the bit again and unlocked
|
|
|
|
|
Logged
|
|
|
|
|
interista82
|
|
« Reply #47 on: August 02, 2011, 09:20:37 PM » |
|
Can't wait to try this!
Buying the parts tomorrow or later today depending on the way you look at it, as it 2.50am in the morning.
I studied the video and he did not drill directly in the centre of the three reference points.
I'm still a bit confused about the cutting of the trace and using the 10-15 ohms resister(Like when do u do that part)
you've need of a 100 ohm resister , not 10/15 ohm  |
|
|
|
|
Logged
|
|
|
|
|
glaze83
|
|
« Reply #48 on: August 02, 2011, 09:26:03 PM » |
|
You need a bbq lighter, not an everyday lighter
|
|
|
|
|
Logged
|
|
|
|
|
99belle99
|
|
« Reply #49 on: August 02, 2011, 09:36:30 PM » |
|
Can't wait to try this!
Buying the parts tomorrow or later today depending on the way you look at it, as it 2.50am in the morning.
I studied the video and he did not drill directly in the centre of the three reference points.
I'm still a bit confused about the cutting of the trace and using the 10-15 ohms resister(Like when do u do that part)
you've need of a 100 ohm resister , not 10/15 ohm . |
|
|
|
« Last Edit: August 02, 2011, 09:42:16 PM by 99belle99 »
|
Logged
|
|
|
|
|
glaze83
|
|
« Reply #50 on: August 02, 2011, 09:37:15 PM » |
|
reading is a skill I understand that... 10-15ohm for mxic , 100ohm for winbond grind unlock
|
|
|
|
|
Logged
|
|
|
|
|
99belle99
|
|
« Reply #51 on: August 02, 2011, 09:38:16 PM » |
|
BTW locked again and tried to unlock with lighter, tried a few times withou success
Just touched the bit again and unlocked
Or just probe again in the hole with a pin conneted to the 100 ohm and 3.3v |
|
|
|
|
Logged
|
|
|
|
|
99belle99
|
|
« Reply #52 on: August 02, 2011, 09:40:01 PM » |
|
reading is a skill I understand that... 10-15ohm for mxic , 100ohm for winbond grind unlock
. |
|
|
|
|
Logged
|
|
|
|
|
modguru
|
|
« Reply #53 on: August 02, 2011, 10:04:31 PM » |
|
in the video the resistor was 2ΚΩ not 100
|
|
|
|
|
Logged
|
|
|
|
|
raidenxtribe
|
|
« Reply #54 on: August 02, 2011, 10:19:57 PM » |
|
Here i am again... Tutz translated in english: http://goo.gl/XqR5sEnjoy  |
|
|
|
« Last Edit: August 02, 2011, 10:38:44 PM by raidenxtribe »
|
Logged
|
|
|
|
|
Pacote-san
|
|
« Reply #55 on: August 02, 2011, 10:21:24 PM » |
|
in the video the resistor was 2ΚΩ not 100
No it was NOT! The color is over saturated (check the YELLOW) It was BROWN so 100ohms :rolleyes: |
|
|
|
|
Logged
|
|
|
|
cyanarnofsky
Newbie
Posts: 9
|
|
« Reply #56 on: August 02, 2011, 10:30:43 PM » |
|
it was 100ohm. The wait begins for TX to catch up with 360pro and JF support
|
|
|
|
|
Logged
|
|
|
|
|
raidenxtribe
|
|
« Reply #57 on: August 02, 2011, 10:33:32 PM » |
|
it was 100ohm. The wait begins for TX to catch up with 360pro and JF support
Lizard Gecko 1.17 is already working with this method ! |
|
|
|
|
Logged
|
|
|
|
|
misterfly
|
|
« Reply #58 on: August 02, 2011, 11:43:29 PM » |
|
Spent some time with Maximus over the mx and wb flashes, while the mx is a piece of cake, the WB is a bitch. There were at least 3 solutions for WB, some more risky, this is less risky one, even if it's not noob friendly. It's even not so much techical in comparison to the others one that had few success rate, or against the ones that had lot of effort and got no result. There are also other possibilities for a software only way, but it's like going blindly searching for a fantomatic "winbond manufacturer mode" (how the hell do they write the serial numb in there? there must be a way), but actually i'm getting lazy. C4eva respect and others, however, like an opinion from Geremia over whether it is possible to actually own writing in 0225
Sorry no Geremia,no Maximus,no Jesus able to write this Soft soundtrack for cooling a bit, ok? Btw, since fw out here have some small differences, prior to go erasing and writing, would be usefull to have fulldump (0225,0225u,0401,xxxx+) ... if you have an app/device that can do it o.c. As usual, use at your own risk, i don't care. Hate it or love it, i don't care. Special thanks to Maximus for cooperating and for supplying test ICs. Congratulations! I tried this test 6 months ago was too destructive, was not a thing to deal with a single mistake or eject the laser does not work  probabily a new solution incoming whitout dremel or small hole ..... |
|
|
|
« Last Edit: August 02, 2011, 11:45:26 PM by misterfly »
|
Logged
|
|
|
|
|
|
|
