MT1335 MX/WB unlocking

[128bit]

Hi all ^_^

I need alternative point for this point whit the ORANGE SQUARE becouse my friend give me the pcb whit the orange selection full broken pad and i want repair for him.


And i want know also if i can use one of this pin? if yes where?


Coz i want try to fix it for example like this whit wire from the pin


But i don't know if i can use the pin,what pin i need to use,and if hav another alternative point before use the pin

[ttz]

just to clarify something after the hole is done we still have to do the sputnik 360 method right?

No sputnik360 is only for MX SPI and the drilling is for Winbond please read before posting  

I know but the drive doesnt get in vendor mode after you make the hole right? to get it in vendor mode we still have to do the cut the trace etc like the sputnik 360 ?

no trace cut with WINBOND
only for MXIC!

[HKFenixgamesDD]

30w soldering iron should give a maximum of 250, after heating, pinch, rotate, as if unsando a drill hole in the IC is minimal!

[HKFenixgamesDD]

just to clarify something after the hole is done we still have to do the sputnik 360 method right?

A few seconds 

[HKFenixgamesDD]

Fenix are you searching for glory ? Try with a glory hole, it's more suited for people like you !

I apologize for trying to help friends.

[ttz]

this is mine  15w --> 320°C  - http://www.modchip.org/product_info.php?products_id=373
so i think that with 30w you can reach more °C than the temp u said  (450°C I think)

[HKFenixgamesDD]

this is mine  15w --> 320°C  - http://www.modchip.org/product_info.php?products_id=373
so i think that with 30w you can reach more than the temp u said

I have no idea of ​​temperature soldering iron 30w

[iLLNESS]

call me crazy, but if your physically cutting the connection with the dremel to unlock, and the point floats after (seems to be since people can relock/etc with a lighter/etc).... what are the odds that ms could just end up detecting this hack later on? im sure the interference inside the 360/etc would be more then enough to pull down/up the connection allowing ms to just 'sit and wait' to see if the drive will try and unlock/lock itself..

correct me if im wrong.

[kayronman]

Yo everyone! I wanna thank the God "Geremia"!!! You're the best!!!
I have a little problem doing this hack! I followed all instructions well but when I drilled the hole, after I've reached the contact inside the chip,
the app (UnlockSPI.exe) said "undervoltage error" with numbers! Please can you tell me what's the problem guys? I'm using a 130ohms resistor and
maybe that's the problem. Thnk you fo your replies!!!

[xbox4g]

if method of iron soldering (HKFenixgamesDD) works great!, but I don't understand how works, becasue Geremia say that the WP wire need to be cut, but it does't no happen using a soldering... weird

[tingedace]

call me crazy, but if your physically cutting the connection with the dremel to unlock, and the point floats after (seems to be since people can relock/etc with a lighter/etc).... what are the odds that ms could just end up detecting this hack later on? im sure the interference inside the 360/etc would be more then enough to pull down/up the connection allowing ms to just 'sit and wait' to see if the drive will try and unlock/lock itself..

correct me if im wrong.

You can't tell directly from software what the WP state is. All you can read back is the SPI status register, which if locked correctly after flashing will be 0x8C irrespective of what the WP line is doing. They'd have to be bombarding the drive with write enable and status register commands to change that status (i.e. what SPIunlocker.exe does), so I'd say pretty unlikely.

[Joka Macer]

so, anyone has get worked with soldering iron only ??

or is just one person seid ?

[mordock]

guys i need some help, using the software geremia provided i get an error,

this is what i get:

Microsoft Windows [Versão 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. Todos os direitos reservados.

C:\>unlockspi D080
WinIO initialized and running

WinIo Error in writing to port D083

C:\>

can any1 hrlp me?

[ttz]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

[mordock]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

i do all my 360s this way, i chance computer when i hear that this or that the other chipset is better, now im using Intel ICH7, and the SATA is ICHI

[deepeastoak]

Can the germania method be done with just a standard viacard like we have always been using or is a x360usb or lizard required?

[DARKFiB3R]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

i do all my 360s this way, i chance computer when i hear that this or that the other chipset is better, now im using Intel ICH7, and the SATA is ICHI

Change it to IDE mode or Compatibility mode or something like that, not RAID or ACHI.

If you have problems booting windows after changing the mode, use this fix http://support.microsoft.com/kb/922976

[Joka Macer]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

i do all my 360s this way, i chance computer when i hear that this or that the other chipset is better, now im using Intel ICH7, and the SATA is ICHI

remember, ICH7 and VIA6421 not work with slims 0225 and above...

[mordock]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

i do all my 360s this way, i chance computer when i hear that this or that the other chipset is better, now im using Intel ICH7, and the SATA is ICHI

remember, ICH7 and VIA6421 not work with slims 0225 and above...

thnx ill use an amd computer then.

can i use an AMD 7** series?
regards

[Joka Macer]

in your bios how did u set sata port? raid? achi? why dont you try with via 6421 or lizard or x360 usb?

i do all my 360s this way, i chance computer when i hear that this or that the other chipset is better, now im using Intel ICH7, and the SATA is ICHI

remember, ICH7 and VIA6421 not work with slims 0225 and above...

thnx ill use an amd computer then.

can i use an AMD 7** series?
regards

AMD should work.