|
CoDeFl@sher
|
 |
« Reply #100 on: October 20, 2011, 05:12:32 PM » |
|
Hello,
I resoldering the two chips (MT and SPI) and now JF detect the drive.But now I have a new problem.When I put the drive in the console the green light blinking again and the drive opens constantly.I close, it opens, I close it opens.I check all wires and everything looks fine.Somebody with similar problem?
Tevez you're almost there, check if the 5 wires from tray motor and tray position switch were soldered from the edge to the center of board in the following sequence:Black,Red,Yelow,Green and White. if ok now with a multimeter, test if the tray status switch is working properly: 1-tray fully open = continuity between White&Yelow wires. 2-tray fully closed = continuity between Green&Yelow wires,and finaly look for solder short or faulty solder on pins 21/22 of MT controller. |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #101 on: October 21, 2011, 01:38:17 AM » |
|
Thank you guys for your help.I noticed there is a short between two wires (tray in and tray out) on the drive when the tray is open.I don't believe there is problem in tray position switch but I will check it.There is no problem in solders on 21/22 pins.The tray open and close normal when I connect it to CK3 Pro.I think the problem is in MT1339e.Will check everything and write again.
|
|
|
|
|
Logged
|
|
|
|
|
manvslife12
|
|
« Reply #102 on: October 25, 2011, 01:24:27 AM » |
|
@ CoDeFl@sher Can you help me find out the problem ? I bought ten MT1339E and SPI. Try to save 2 PCB of my xbox. I Checked every single leg in MT1339E  JF can't detect my drive . Try many way : With the SPI and Without the SPI Replace MT1339E with orther one Check every single (my eye >.<) Try with two PCB replace MT Everything JF still can't detect it   |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #103 on: October 25, 2011, 02:07:32 AM » |
|
@manvslife12
You have wrong.You're swap 5,6,7 and 8 pins on the SPI. Just solder it in reverse.Then your drive still can't find in JF couse is blank.You need to put in Vendor mode.
|
|
|
|
|
Logged
|
|
|
|
|
manvslife12
|
|
« Reply #104 on: October 25, 2011, 02:41:05 AM » |
|
@manvslife12
You have wrong.You're swap 5,6,7 and 8 pins on the SPI. Just solder it in reverse.Then your drive still can't find in JF couse is blank.You need to put in Vendor mode.
Yeah, thanks you so much resolded 5 6 7 8 in JP it can't detect it because it need to vendor mode >.< when jf doesn't detect it i stop everything because i thinks it broken leg or something >.< Thanks you Tevez 1 more question. When i write FW and the last step is click 0x00 for lock it to 0x8C. outro ok. is there any step to do  because i see in the jftut1.4.4.pdf it said need to switch something Thanks you so much again  |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #105 on: October 25, 2011, 04:09:21 AM » |
|
This switch is for hardware lock for SPI.It's option and you can hardware lock your SPI - just put wire between MPX01 point and Ground.
|
|
|
|
|
Logged
|
|
|
|
|
manvslife12
|
|
« Reply #106 on: October 25, 2011, 04:14:35 AM » |
|
This switch is for hardware lock for SPI.It's option and you can hardware lock your SPI - just put wire between MPX01 point and Ground.
If i don't hardware lock for SPI, everything is ok ? My stupid question : Why i must hardware lock SPI ? |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #107 on: October 25, 2011, 05:40:09 AM » |
|
M$ lock SPI hardware.In this case you make your drive just like M$ lock it.I think it not necessary.If you lock it next time when you need flashing you need to unlock.
|
|
|
|
|
Logged
|
|
|
|
|
CoDeFl@sher
|
|
« Reply #108 on: October 25, 2011, 09:54:27 AM » |
|
This switch is for hardware lock for SPI.It's option and you can hardware lock your SPI - just put wire between MPX01 point and Ground.
Tevez & manvslife12 to hardware lock SPI you must put a wire between pin3 of SPI (WP) and ground. |
|
|
|
|
Logged
|
|
|
|
|
manvslife12
|
|
« Reply #109 on: October 25, 2011, 09:02:20 PM » |
|
Tevez & manvslife12 to hardware lock SPI you must put a wire between pin3 of SPI (WP) and ground.
Thanks You CoDeFl@sher i will make a switch between Pin3 Ground and Pin7 8 |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #110 on: October 26, 2011, 05:13:14 AM » |
|
This switch is for hardware lock for SPI.It's option and you can hardware lock your SPI - just put wire between MPX01 point and Ground.
Tevez & manvslife12 to hardware lock SPI you must put a wire between pin3 of SPI (WP) and ground. Whatever, I don't hardware lock SPI.Most import for me it's I decide the problem with ejecting.The problem was resistor R47 in the right side of controller (you can see it on the picture up). So if somebody have problem with tray aways opening just check R47. |
|
|
|
|
Logged
|
|
|
|
|
gavingt
|
|
« Reply #111 on: October 26, 2011, 05:53:53 AM » |
|
Whatever, I don't hardware lock SPI.
Can't Microsoft check for this rather easily? I wouldn't risk it. |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #112 on: November 01, 2011, 09:26:23 AM » |
|
Whatever, I don't hardware lock SPI.
Can't Microsoft check for this rather easily? I wouldn't risk it. I don't know. I want ask did somebody made dashbord update on console with that PCB board and LT 2.0? And if made what was the SPI - hardware locked or unlocked? |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #113 on: November 20, 2011, 03:38:28 PM » |
|
I finished my dual firmware mod. Replaced the MT1335 with a MT1339 + two SPI memories. Original firmware is in a Winbond SPI with proper hw and sw locks. Hacked firmware is in a MXIC SPI. Also with different drive key (RGH NAND image got different keyvault and drive key)  |
|
|
|
|
Logged
|
|
|
|
|
|
|
k0mpresd
|
|
« Reply #115 on: December 12, 2011, 12:35:01 PM » |
|
if anybody is looking, ive got a few extra sets of these.  |
|
|
|
|
Logged
|
|
|
|
|
galo911
|
|
« Reply #116 on: December 22, 2011, 08:33:09 AM » |
|
Congratulations. This is a great addon for any dual boot setup... Will any of you guys make a small tut on this ?
|
|
|
|
|
Logged
|
|
|
|
|
phonsey
|
|
« Reply #117 on: December 28, 2011, 02:55:38 AM » |
|
if anybody is looking, ive got a few extra sets of these. can you p.m me the details for buying one off you m8  |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #118 on: December 28, 2011, 02:59:32 AM » |
|
Congratulations. This is a great addon for any dual boot setup... Will any of you guys make a small tut on this ?
All the info you need is in this thread. I may do a schematic for the connection but no tutorial. The dual firmware is part of this switch mod: http://www.xboxhacker.org/index.php?topic=17584.msg132399#msg132399 |
|
|
|
|
Logged
|
|
|
|
|
galo911
|
|
« Reply #119 on: January 05, 2012, 09:56:47 PM » |
|
Where you parked the 2nd SPI ? Can't see it on the picture. Is it on the other side?
|
|
|
|
|
Logged
|
|
|
|
|
