|
k0mpresd
|
 |
« Reply #80 on: October 08, 2011, 09:49:38 AM » |
|
no.
|
|
|
|
|
Logged
|
|
|
|
|
astralev
|
|
« Reply #81 on: October 13, 2011, 02:32:37 AM » |
|
Hello
Sorry my bad english !
I change 1335 with 1339E , get spy from benq wad 6038.
Leg 3,7,8 together solder to mpx01.
Spy show in vendor mode in jungleflash 1.89, show erase when check, verify failed.
Spy write blank 1,2,3,4 Ok check verify failed.
Show erase, and writing but not rwite really nothing.
I dont know why ? Pleace any help!
Sending Vendor Intro to port 0xdc00
Status 0x80
Re-sending Vendor Intro:
..............
Serial flash found with Status 0x72
Sending Device ID request to port 0xdc00
Spi Status: 0x00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Getting Status from port 0xdc00
SPi flash found with Status 0x72
Sending Chip Erase to Port 0xdc00
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification failed !
Maybe i solder diferrent point or power for spy. Need another spy install diagram
|
|
|
|
« Last Edit: October 13, 2011, 02:41:26 AM by astralev »
|
Logged
|
|
|
|
|
CoDeFl@sher
|
|
« Reply #82 on: October 13, 2011, 11:38:06 AM » |
|
Hello
Sorry my bad english !
I change 1335 with 1339E , get spy from benq wad 6038.
Leg 3,7,8 together solder to mpx01.
Spy show in vendor mode in jungleflash 1.89, show erase when check, verify failed.
Spy write blank 1,2,3,4 Ok check verify failed.
Show erase, and writing but not rwite really nothing.
I dont know why ? Pleace any help!
Sending Vendor Intro to port 0xdc00
Status 0x80
Re-sending Vendor Intro:
..............
Serial flash found with Status 0x72
Sending Device ID request to port 0xdc00
Spi Status: 0x00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Getting Status from port 0xdc00
SPi flash found with Status 0x72
Sending Chip Erase to Port 0xdc00
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification failed !
Maybe i solder diferrent point or power for spy. Need another spy install diagram
Hi astralev,to help you I need a picture showing the wire connection between SPI and MT1339. |
|
|
|
|
Logged
|
|
|
|
|
brunosso
|
|
« Reply #83 on: October 14, 2011, 06:41:01 AM » |
|
appearantly the drives used for kreons have the controller/spi needed.. samsung sh-d163. but odds are youll be paying more for this drive since it was in demand at one point in the past to use with kreons  I have disassembled a SH-D163B right now, but there is no MT1339, it is an MT1309. What a pity... Does it have to be D163C? EDIT: Yeah, bought a D163C and there is a MT1339E in it. there is also the MX?? |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #84 on: October 19, 2011, 04:28:49 AM » |
|
Placing a switch to pin #1 allows you to switch between two SPI chips. Right?
I'm going to try this on my slim. I got extra MX25L2005 and MT1339 chips. I'll use original image for non-hacked mode and iXtreme LT+ 2.0 for hacked/glitched mode.
Can M$ detect the SPI chip model? MXIC or Winbond? Should I use Winbond w25p20 for the original image?
|
|
|
|
|
Logged
|
|
|
|
|
CoDeFl@sher
|
|
« Reply #85 on: October 19, 2011, 08:16:50 AM » |
|
Placing a switch to pin #1 allows you to switch between two SPI chips. Right?
I'm going to try this on my slim. I got extra MX25L2005 and MT1339 chips. I'll use original image for non-hacked mode and iXtreme LT+ 2.0 for hacked/glitched mode.
Can M$ detect the SPI chip model? MXIC or Winbond? Should I use Winbond w25p20 for the original image?
d4m4n if the original drive was MXIC embedded,use MX25L2005 spi. if Winbond,use W25P20 spi.I never tryed Dual SPI but,if you want to test don't forget to select the spi you want to boot before power on the system. |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #86 on: October 19, 2011, 08:27:39 AM » |
|
Placing a switch to pin #1 allows you to switch between two SPI chips. Right?
I'm going to try this on my slim. I got extra MX25L2005 and MT1339 chips. I'll use original image for non-hacked mode and iXtreme LT+ 2.0 for hacked/glitched mode.
Can M$ detect the SPI chip model? MXIC or Winbond? Should I use Winbond w25p20 for the original image?
d4m4n if the original drive was MXIC embedded,use MX25L2005 spi. if Winbond,use W25P20 spi.I never tryed Dual SPI but,if you want to test don't forget to select the spi you want to boot before power on the system. Anyone got extra W25P20 chips? Or is there some dvd drive model with this chip inside? The spi chips will be wired to the same switch that I use for nonhacked/RGH-mode. It will be used when the machine is powered off. |
|
|
|
|
Logged
|
|
|
|
|
playonlcd
|
|
« Reply #87 on: October 19, 2011, 08:58:47 AM » |
|
On TX boards there is Windbond W25X20BVNIG SPI. Hello
Sorry my bad english !
I change 1335 with 1339E , get spy from benq wad 6038.
Leg 3,7,8 together solder to mpx01.
Do you have 3.3V on MPX01? From the scheme it seems that 3.3v is on a lower pad, on the right of the resistance. Cya! |
|
|
|
« Last Edit: October 19, 2011, 09:30:31 AM by playonlcd »
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #88 on: October 19, 2011, 01:33:02 PM » |
|
Hello, I'm new in this forum and I need help.
First sorry for may bad english.
I have a Xbox360 SLIM with drive marked as 9504 but JF say it's 0225.It's Windbond.
So I replace the MT1339WE controller with MT1339E + MX25L2005MC.
Everything goes well I flashed the new SPI with JF and it give to me everything fine until I power off the Drive.When I power of the drive and on again JF say to me "No Drive detected". The console can't recognize the drive too. The user @cashimi001 have the same problem in first page but no body answer him.I read every forum and I don't know what is the problem.May me the SPI problem, but it lock and unlock well and I can write the firmware without issue.Can somebody tell me what I do?
I can post JF log if nessesary.
I use X360PRO and CK3 Pro.
Thanks.
|
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #89 on: October 19, 2011, 02:51:01 PM » |
|
On TX boards there is Windbond W25X20BVNIG SPI. Do you mean the Xecuter Pro Kit white PCB with the SPI chip? If yes then I have to look for one. I have installed one but did not check the SPI model. |
|
|
|
|
Logged
|
|
|
|
|
CoDeFl@sher
|
|
« Reply #90 on: October 19, 2011, 03:11:37 PM » |
|
Hello, I'm new in this forum and I need help.
First sorry for may bad english.
I have a Xbox360 SLIM with drive marked as 9504 but JF say it's 0225.It's Windbond.
So I replace the MT1339WE controller with MT1339E + MX25L2005MC.
Everything goes well I flashed the new SPI with JF and it give to me everything fine until I power off the Drive.When I power of the drive and on again JF say to me "No Drive detected". The console can't recognize the drive too. The user @cashimi001 have the same problem in first page but no body answer him.I read every forum and I don't know what is the problem.May me the SPI problem, but it lock and unlock well and I can write the firmware without issue.Can somebody tell me what I do?
I can post JF log if nessesary.
I use X360PRO and CK3 Pro.
Thanks.
Try to use short wires between spi and MT controller,and after perform a write operation press the "Outro/ATA Reset"button twice before power off the drive. |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #91 on: October 19, 2011, 03:21:00 PM » |
|
On TX boards there is Windbond W25X20BVNIG SPI. Do you mean the Xecuter Pro Kit white PCB with the SPI chip? If yes then I have to look for one. I have installed one but did not check the SPI model. The W25 P20 and W25 X20 both work? The X model is available from Digikey. |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #92 on: October 19, 2011, 03:36:03 PM » |
|
Hello, I'm new in this forum and I need help.
First sorry for may bad english.
I have a Xbox360 SLIM with drive marked as 9504 but JF say it's 0225.It's Windbond.
So I replace the MT1339WE controller with MT1339E + MX25L2005MC.
Everything goes well I flashed the new SPI with JF and it give to me everything fine until I power off the Drive.When I power of the drive and on again JF say to me "No Drive detected". The console can't recognize the drive too. The user @cashimi001 have the same problem in first page but no body answer him.I read every forum and I don't know what is the problem.May me the SPI problem, but it lock and unlock well and I can write the firmware without issue.Can somebody tell me what I do?
I can post JF log if nessesary.
I use X360PRO and CK3 Pro.
Thanks.
Try to use short wires between spi and MT controller,and after perform a write operation press the "Outro/ATA Reset"button twice before power off the drive. Yes, I press Outro twise and JF tells me I have a 0225 drive with veryfied key. I'll try short wires and write what is the result.Thanks. |
|
|
|
|
Logged
|
|
|
|
|
rolf2
|
|
« Reply #93 on: October 19, 2011, 07:45:49 PM » |
|
Someone brave enough to destroy internal mt1335we spi flash with dremel to try to solder external SPI with hope that if internal flash not found - mt1335we will try to use external spi ?  |
|
|
|
« Last Edit: October 19, 2011, 07:51:12 PM by rolf2 »
|
Logged
|
|
|
|
|
CoDeFl@sher
|
|
« Reply #94 on: October 19, 2011, 08:41:44 PM » |
|
On TX boards there is Windbond W25X20BVNIG SPI. Do you mean the Xecuter Pro Kit white PCB with the SPI chip? If yes then I have to look for one. I have installed one but did not check the SPI model. The W25 P20 and W25 X20 both work? The X model is available from Digikey. d4m4n take a look on datasheets of both W25P20 / W25X20, and choose that with same Manufacturer ID and Device ID of your original spi. |
|
|
|
|
Logged
|
|
|
|
|
d4m4n
|
|
« Reply #95 on: October 20, 2011, 01:11:39 AM » |
|
d4m4n take a look on datasheets of both W25P20 / W25X20, and choose that with same Manufacturer ID and Device ID of your original spi.
Thanks for the hint. They both seem to have the same ID's. |
|
|
|
|
Logged
|
|
|
|
|
gavingt
|
|
« Reply #96 on: October 20, 2011, 05:51:44 AM » |
|
I have an MT1339e controller chip and an MX25L2005 spi flash chip for sale if anyone's interested. $25 plus shipping for the pair, shipped from Arizona. These are the two components needed to do this mod. The MT1339e came from a brand new Lite-On drive (which I paid about $25 for a few months back and never did anything with), and the MX25L2005 came from an old Benq drive of mine. I've had them lying around as a backup, just in case I botched a Kamikaze hack. But I've pretty much perfected my Kamikaze at this point, so I doubt I'll ever use them. I was very careful in lifting both, so I can guarantee you that they're fully functional. PM or email me at gavingt@gmail.com. |
|
|
|
|
Logged
|
|
|
|
|
playonlcd
|
|
« Reply #97 on: October 20, 2011, 10:02:38 AM » |
|
On TX boards there is Windbond W25X20BVNIG SPI. Do you mean the Xecuter Pro Kit white PCB with the SPI chip? If yes then I have to look for one. I have installed one but did not check the SPI model. No, not from pro kits. I am talking about those from replacements pcb boards from TX. Yes, W25X2 is available on digikey if is a must to run the same spi. But TX came later with an 2 spi pcb board, and nobody knows for sure if that matters or not. |
|
|
|
|
Logged
|
|
|
|
|
Tevez
|
|
« Reply #98 on: October 20, 2011, 01:34:14 PM » |
|
Hello,
I resoldering the two chips (MT and SPI) and now JF detect the drive.But now I have a new problem.When I put the drive in the console the green light blinking again and the drive opens constantly.I close, it opens, I close it opens.I check all wires and everything looks fine.Somebody with similar problem?
|
|
|
|
|
Logged
|
|
|
|
|
playonlcd
|
|
« Reply #99 on: October 20, 2011, 03:01:45 PM » |
|
Hello,
I resoldering the two chips (MT and SPI) and now JF detect the drive.But now I have a new problem.When I put the drive in the console the green light blinking again and the drive opens constantly.I close, it opens, I close it opens.I check all wires and everything looks fine.Somebody with similar problem?
I was having this issue twice. Once was because of the switch witch is signaling the tray closing, the one with yellow cables, was moving from is location The second is after an kamikaze applied the tray don't stay close. I'll let you know if replacing the MT is fixing the problem. |
|
|
|
|
Logged
|
|
|
|
|
