|
daverboon
|
 |
« on: February 02, 2010, 08:37:55 PM » |
|
awhile back i flashed a hitachi drive and then got console banned with the nov 09 ban wave. since then i've gotten a new box with a benq in it and i'm wondering if i can swap in the flashed hitachi to play my backups?
|
|
|
|
« Last Edit: February 03, 2010, 02:43:20 PM by daverboon »
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #1 on: February 02, 2010, 08:40:34 PM » |
|
no matter what your going to have to get the key off the benq drive to flash back to the Hitachi drive...
why not just flash the benq drive and use that?
|
|
|
|
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
Gazcoigne
|
|
« Reply #2 on: February 02, 2010, 08:41:09 PM » |
|
much easier to flash benq drive than muck about with the hitachi
then youd have to dump both drives. cross spoof etc
less work and hassle to do benq only
|
|
|
|
|
Logged
|
|
|
|
|
daverboon
|
|
« Reply #3 on: February 02, 2010, 08:46:20 PM » |
|
no matter what your going to have to get the key off the benq drive to flash back to the Hitachi drive...
why not just flash the benq drive and use that?
well i could and that would certaily be the easiest way. it's currently a cb5766, is there a way to get updates without going past the point of being able to exploit the box? i can't do it on my own so i'm searching for someone in my area that'll do the hack for me. |
|
|
|
|
Logged
|
|
|
|
|
Grandmaster
|
|
« Reply #4 on: February 02, 2010, 08:59:05 PM » |
|
Im lost here on this post you are 1st asking about dvd drive flashing or spoffing a benq info over to a hitachi.. Now you seem to be replying to a post but on the topic of nand flashing and cb versions.. Im confused
|
|
|
|
|
Logged
|
|
|
|
|
daverboon
|
|
« Reply #5 on: February 02, 2010, 09:09:05 PM » |
|
Im lost here on this post you are 1st asking about dvd drive flashing or spoffing a benq info over to a hitachi.. Now you seem to be replying to a post but on the topic of nand flashing and cb versions.. Im confused
The reason i'm asking about the drives is because i've been trying to jtag my falcon for the last 5 days but I couldn't get the DB1F1 point to stick so I gave up on that. My box is still exploitable but because the dash is soo friggin old I can't do much with it without needing updates. Atleast that's the message I keep getting. I have a hitachi drive that's flashed and that's why I was wondering. Or should I just forget about the jtag and update my 360 then flash the benq. I don't want to get console banned again but in it's current dash I can't install to HDD, watch movies from the usb stick or play backups. |
|
|
|
|
Logged
|
|
|
|
|
littlestevie360
|
|
« Reply #6 on: February 02, 2010, 09:11:56 PM » |
|
Im lost here on this post you are 1st asking about dvd drive flashing or spoffing a benq info over to a hitachi.. Now you seem to be replying to a post but on the topic of nand flashing and cb versions.. Im confused
The reason i'm asking about the drives is because i've been trying to jtag my falcon for the last 5 days but I couldn't get the DB1F1 point to stick so I gave up on that. My box is still exploitable but because the dash is soo friggin old I can't do much with it without needing updates. Atleast that's the message I keep getting. I have a hitachi drive that's flashed and that's why I was wondering. Or should I just forget about the jtag and update my 360 then flash the benq. I don't want to get console banned again but in it's current dash I can't install to HDD, watch movies from the usb stick or play backups. maybe look at an alt point for DB1F1 seriously dont go doing something silly like updating a JTAG exploitable console willingly |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #7 on: February 02, 2010, 09:16:35 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
|
|
|
|
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #8 on: February 02, 2010, 09:20:01 PM » |
|
Im lost here on this post you are 1st asking about dvd drive flashing or spoffing a benq info over to a hitachi.. Now you seem to be replying to a post but on the topic of nand flashing and cb versions.. Im confused
The reason i'm asking about the drives is because i've been trying to jtag my falcon for the last 5 days but I couldn't get the DB1F1 point to stick so I gave up on that. My box is still exploitable but because the dash is soo friggin old I can't do much with it without needing updates. Atleast that's the message I keep getting. I have a hitachi drive that's flashed and that's why I was wondering. Or should I just forget about the jtag and update my 360 then flash the benq. I don't want to get console banned again but in it's current dash I can't install to HDD, watch movies from the usb stick or play backups. maybe look at an alt point for DB1F1 seriously dont go doing something silly like updating a JTAG exploitable console willingly I've looked m8, seriously. I've asked around, i've googled for it. There doesn't seem to be an alternate point so for the time being i'll wait and see if I can locate someone to do the setup for me. I totally hear ye, finding an exploitable 360 nowadays is tough and I just happened to have a friend with one that never used his. So he traded it for my old refurbished one. |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #9 on: February 02, 2010, 09:23:14 PM » |
|
you looked not to far it's all here for the alt spots  DB1F1 alt spots < i also give you a link to it.lol |
|
|
|
« Last Edit: February 02, 2010, 09:35:20 PM by ReverseAffect »
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #10 on: February 02, 2010, 09:33:24 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
OMG!! I just found a thread that says the FT1U2 point on the underside of the board will work as an alternate and then another near it can be used as well but near impossible to solder. FRIG!! That near ompossible one was the one i've been trying to get. |
|
|
|
|
Logged
|
|
|
|
|
littlestevie360
|
|
« Reply #11 on: February 02, 2010, 09:36:47 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
OMG!! I just found a thread that says the FT1U2 point on the underside of the board will work as an alternate and then another near it can be used as well but near impossible to solder. FRIG!! That near ompossible one was the one i've been trying to get. personally i find FT1U2 to be the easiest to do, both on the level of getting it to flow correctly, and because i like to run my JTAG wires on the underside of the board |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #12 on: February 02, 2010, 09:38:41 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
OMG!! I just found a thread that says the FT1U2 point on the underside of the board will work as an alternate and then another near it can be used as well but near impossible to solder. FRIG!! That near ompossible one was the one i've been trying to get. personally i find FT1U2 to be the easiest to do, both on the level of getting it to flow correctly, and because i like to run my JTAG wires on the underside of the board yep and now we have a shorter distance(no mater what point) it is well worth it on the bottom....solder it up and glue it down..... |
|
|
|
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #13 on: February 02, 2010, 09:40:35 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
OMG!! I just found a thread that says the FT1U2 point on the underside of the board will work as an alternate and then another near it can be used as well but near impossible to solder. FRIG!! That near ompossible one was the one i've been trying to get. personally i find FT1U2 to be the easiest to do, both on the level of getting it to flow correctly, and because i like to run my JTAG wires on the underside of the board Right on, i'll be tryin that tonight. which version of xbr should i use? i have the 8955_3a from xbins but I couldn't find any xell |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #14 on: February 02, 2010, 09:45:41 PM » |
|
yes, as littlestevie360 said you got to be crazy to update that jtagable box.......
OMG!! I just found a thread that says the FT1U2 point on the underside of the board will work as an alternate and then another near it can be used as well but near impossible to solder. FRIG!! That near ompossible one was the one i've been trying to get. personally i find FT1U2 to be the easiest to do, both on the level of getting it to flow correctly, and because i like to run my JTAG wires on the underside of the board Right on, i'll be tryin that tonight. which version of xbr should i use? i have the 8955_3a from xbins but I couldn't find any xell for the falcon thats the file and xell is built in...after you flash it just power down for 25 secs and then power back up using the eject button... after you get that all together you can then be guided to patching in redline99s new XeLLous... |
|
|
|
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #15 on: February 02, 2010, 10:15:10 PM » |
|
for the falcon thats the file and xell is built in...after you flash it just power down for 25 secs and then power back up using the eject button...
after you get that all together you can then be guided to patching in redline99s new XeLLous...
Thank you all sooo much for answering me on this. I had almost done a terrible thing out of desperation. |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #16 on: February 02, 2010, 10:21:28 PM » |
|
for the falcon thats the file and xell is built in...after you flash it just power down for 25 secs and then power back up using the eject button...
after you get that all together you can then be guided to patching in redline99s new XeLLous...
Thank you all sooo much for answering me on this. I had almost done a terrible thing out of desperation. ya i and others will bash you on not using search...(but this isn't the case here) search has been a iffy thing ,also with the advanced search... so don't loose us...post what you need to post here so you can get up and running and always save an orig valid backup to a stick,disk or whatever in case P.S do we want to know? I had almost done a terrible thing out of desperation......lol |
|
|
|
« Last Edit: February 02, 2010, 10:23:17 PM by ReverseAffect »
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #17 on: February 02, 2010, 11:50:28 PM » |
|
ya i and others will bash you on not using search...(but this isn't the case here) search has been a iffy thing ,also with the advanced search... so don't loose us...post what you need to post here so you can get up and running and always save an orig valid backup to a stick,disk or whatever in case P.S do we want to know? I had almost done a terrible thing out of desperation......lol lol terrible as in updating an exploitable box. this is nuts! i tried for the FT1u2 and right after the solder hardened the point popped out and broke off the lead grr, so i went back to the other "near impossible" one next to it and scraped away some of the lead coating to get a better grip on it. so far it's sticking |
|
|
|
|
Logged
|
|
|
|
|
ReverseAffect
|
|
« Reply #18 on: February 03, 2010, 12:04:55 AM » |
|
ahh... problem is this isn't lead coating it's a board protective coating(sorry forgot the name) ...it is all lead free solder, already on the board.
so it has to be a bit hotter to mend your wire.
your soldering a wire to that point right? not the diode?
and don't hold it on to long...if it don't mend your tip isn't clean...and are you using about a pinhead amount of flux?
it will clean the area as you heat down the wire......let the wire slip down the tip to hit the trace...that wires heat is sufficient enough to heat/mend the wire to the trace...
|
|
|
|
« Last Edit: February 03, 2010, 12:11:39 AM by ReverseAffect »
|
Logged
|
sick like a mofo..not reballing for a while...
|
|
|
|
daverboon
|
|
« Reply #19 on: February 03, 2010, 12:19:50 AM » |
|
ahh... problem is this isn't lead coating it's a board protective coating(sorry forgot the name) ...it is all lead free solder, already on the board.
so it has to be a bit hotter to mend your wire.
your soldering a wire to that point right? not the diode?
and don't hold it on to long...if it don't mend your tip isn't clean...and are you using about a pinhead amount of flux?
it will clean the area as you heat down the wire......let the wire slip down the tip to hit the trace...that wires heat is sufficient enough to heat/mend the wire to the trace...
no diode to that point? all the diagrams use a diode. crap i soldered the diode on, currently flashing the xbr to see if it took what i meant was the little hole or dot you solder to popped right out and broke away from the leed(don't know the actual term) so it's now this thin line that runs to an empty hole it took!!! i booted it up by the eject and xell loaded but i got a bunch of error codes about cb |
|
|
|
« Last Edit: February 03, 2010, 01:10:09 AM by daverboon »
|
Logged
|
|
|
|
|
Dilber MC Theme by HarzeM