|
Dream
|
 |
« Reply #400 on: May 24, 2010, 06:30:05 AM » |
|
Hi Dream, thank you for your help, the problem i'm having is - i cant get JF to see the vendor properties, ive built your probe ready but i cant get a vendor, any ideas ?
Wrong sata port. (I/O Port) OR Short-circuit 3,3 to GND. |
|
|
|
|
Logged
|
|
|
|
lyalenko
Newbie
Posts: 8
|
|
« Reply #401 on: May 24, 2010, 01:09:19 PM » |
|
lyalenko,
Clean your lo board and take new picture.
You mean my attempts to restore the track? |
|
|
|
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #402 on: May 25, 2010, 06:59:41 AM » |
|
lyalenko,
If you like to fix it?
|
|
|
|
|
Logged
|
|
|
|
lyalenko
Newbie
Posts: 8
|
|
« Reply #403 on: May 25, 2010, 08:08:16 AM » |
|
lyalenko,
If you like to fix it?
English is not my native language, and I not understand what foto you mean? Clean lite on board, and make foto without this things (it's from from first foto)? http://img704.imageshack.us/img704/8199/64678952.jpgor you mean foto after execution your instructions? I don't have any "hardware toolls", just soldering-iron  |
|
|
|
« Last Edit: May 25, 2010, 09:51:12 AM by lyalenko »
|
Logged
|
|
|
|
noobiedoo
Newbie
Posts: 4
|
|
« Reply #404 on: May 25, 2010, 09:20:12 AM » |
|
Hey dream
Sorry for late reply.
Yes there is a short on 1.8v line but dont know where ?
What can i do to stop it shorting out.
There is nothing on the top of the board shorting it as i have cleaned it using a fibre pen.
It must be on the chip side?
|
|
|
|
|
Logged
|
|
|
|
amarok
Newbie
Posts: 1
|
|
« Reply #405 on: May 25, 2010, 11:56:00 AM » |
|
ok so I have a problem too. I screwed up R101, tried the MRA, but cant find the drive. Seems im doing something wrong.. I hope you can help me out. See images below:  and a pic from the other side  |
|
|
|
« Last Edit: May 25, 2010, 12:15:14 PM by amarok »
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #406 on: May 26, 2010, 06:18:34 AM » |
|
amarok, Measure resistance 3,3V to GND. noobiedoo, Measure resistance 1,8V to GND. lyalenko, Take all wires off and clean it, take new picture. My own language is finnish.  |
|
|
|
|
Logged
|
|
|
|
noobiedoo
Newbie
Posts: 4
|
|
« Reply #407 on: May 26, 2010, 07:06:06 AM » |
|
noobiedoo,
Measure resistance 1,8V to GND. thanks for replying dream. It's reading. 0.6 - 0.9 ohms. |
|
|
|
|
Logged
|
|
|
|
|
|
|
Dream
|
|
« Reply #409 on: May 27, 2010, 02:29:36 AM » |
|
lyalenko, Make easy probe page 4 reply 66. Install Jump wires and measure 3,3V to GND 95K ohm - 110 Kohm is good. If it is mega ohms then i will make you new dump/repair picture.  This is stock Fix.  |
|
|
|
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #410 on: May 27, 2010, 02:35:50 AM » |
|
noobiedoo,
Measure resistance 1,8V to GND. thanks for replying dream. It's reading. 0.6 - 0.9 ohms. Are you reading it correctly. It should be around 700 K ohm. If it is 0.6 ohm the mt chip maybe damaged. |
|
|
|
|
Logged
|
|
|
|
Xzibit
Newbie
Posts: 2
|
|
« Reply #411 on: May 27, 2010, 02:33:02 PM » |
|
Hey Dream, i've been following the topic from the beginning but can't seem to find a solution to my problem. I lifted pin 101, 122 and C02 on the other side of the board. Is there still hope? I can't seem to get hi res picture of the board this evening, i don't have a good enough camera..  |
|
|
|
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #412 on: May 28, 2010, 04:16:46 AM » |
|
Hey Dream, i've been following the topic from the beginning but can't seem to find a solution to my problem. I lifted pin 101, 122 and C02 on the other side of the board. Is there still hope? I can't seem to get hi res picture of the board this evening, i don't have a good enough camera.. Do you have the firmware? What was the modding style? |
|
|
|
« Last Edit: May 28, 2010, 04:24:44 AM by Dream »
|
Logged
|
|
|
|
noobiedoo
Newbie
Posts: 4
|
|
« Reply #413 on: May 28, 2010, 11:01:21 AM » |
|
Again sorry for the late reply dream. It's my fault it's actually 6.0 - 9.0 ohms. (TYPO)  |
|
|
|
|
Logged
|
|
|
|
Xzibit
Newbie
Posts: 2
|
|
« Reply #414 on: May 28, 2010, 11:42:08 AM » |
|
Hey Dream, i've been following the topic from the beginning but can't seem to find a solution to my problem. I lifted pin 101, 122 and C02 on the other side of the board. Is there still hope? I can't seem to get hi res picture of the board this evening, i don't have a good enough camera.. Do you have the firmware? What was the modding style? Unfortunately not.. I followed the Xecuter guide since i had their LT switch. |
|
|
|
|
Logged
|
|
|
|
saint_camus
Newbie
Posts: 1
|
|
« Reply #415 on: May 28, 2010, 11:50:58 PM » |
|
I need your help guys, I have this problem, do u know how to fix this. sorry 4 the picture.  best regards |
|
|
|
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #416 on: May 29, 2010, 02:00:55 AM » |
|
Xzibit, Make easy probe page 4 reply 66 and dump it. Dump  Fix  |
|
|
|
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #417 on: May 29, 2010, 02:03:20 AM » |
|
saint_camus use lyalenkos pictures or LT Fakir it.
|
|
|
|
|
Logged
|
|
|
|
lyalenko
Newbie
Posts: 8
|
|
« Reply #418 on: May 29, 2010, 11:05:13 AM » |
|
lyalenko,
Make easy probe page 4 reply 66.
Install Jump wires and measure 3,3V to GND 95K ohm - 110 Kohm is good.
If it is mega ohms then i will make you new dump/repair picture.
Bad day   http://img179.imageshack.us/img179/1926/dsc08057k.jpgNow it's a brick? (Element unsoldered and flew) |
|
|
|
« Last Edit: May 29, 2010, 11:08:04 AM by lyalenko »
|
Logged
|
|
|
|
|
Dream
|
|
« Reply #419 on: May 29, 2010, 12:59:58 PM » |
|
lyalenko,
Send the board to me i can fix it for you.
|
|
|
|
|
Logged
|
|
|
|
|
Dilber MC Theme by HarzeM