|
xboxer1234
|
 |
« Reply #1000 on: January 01, 2011, 12:43:45 AM » |
|
hi dream i have a 74850c here it had ix lt v1.1 on trying to update to LT+ for the new games like u do when dumping the FW with JF i get all 7777777777777777777777 now when testing points on the board i get a short from the points in the pic  im sure the other point is GND any help is greatly apreciated mate i have another board here and them points are not shorted so im thinking somethgin has gone somewhere. the drive picks up in JF and i get status 72 and chip/drive properties just fine. just get the 7777777777777777  grrrrr thanks dave Do you have the original fw (or the one that has correct dvd key)? If not, try to press CTRL+F12 on Jungleflasher, it should open a list of dvd keys. If that is empty too, try to check the JF log. The reason (most likely) why the dvd key is 777777777777... is because you didn't copy the original dvd key to lt+. |
|
|
|
|
Logged
|
|
|
|
madmackem
Newbie
Posts: 3
|
|
« Reply #1001 on: January 01, 2011, 11:19:40 AM » |
|
if you couldn't fix it by fixing it, then you can't fix it. maybe try letting one of us take a shot at it.
Hi Shaggy, I dont know if you were replying to me or not, I havent attempted to "fix it" yet. I would like to fit it with the lt switch using wires, not direct to the board. Where would I attach the wire instead of the lifted pad? I've seen the diag with the wire from the resistor under the resin to r207 - do I need to fit that wire first to get a dump or after the dump? Cheers |
|
|
|
|
Logged
|
|
|
|
|
pkmz
|
|
« Reply #1002 on: January 01, 2011, 11:53:37 AM » |
|
Don't use LT switch honestly. They're way to hard to solder.
Just make cuts, solder wires, dump,flash desolder wires and continue your day. Takes roughly 20 minutes.
|
|
|
|
|
Logged
|
|
|
|
madmackem
Newbie
Posts: 3
|
|
« Reply #1003 on: January 01, 2011, 05:25:16 PM » |
|
Anyone in the UK who can fix it please feel free to pm me! Ok I cleaned it up ! now the xtractor powers up when i connect it, I hope its a good thing. http://i813.photobucket.com/albums/zz55/madmackem_uk/2010-12-31203716-1.jpg [/quote] I have managed to get the board dumped and flashed using the lt switch and a pin in the hole. Can anyone tell me what i need to do to get it back to "normal" after i remove the lt switch please? never mind, found a guy in uk to fix it. cheers guys great thread just wish I was better with an iron in my hand! |
|
|
|
« Last Edit: January 01, 2011, 06:39:02 PM by madmackem »
|
Logged
|
|
|
|
|
dave11674
|
|
« Reply #1004 on: January 02, 2011, 08:02:00 PM » |
|
hi dream i have a 74850c here it had ix lt v1.1 on trying to update to LT+ for the new games like u do when dumping the FW with JF i get all 7777777777777777777777 now when testing points on the board i get a short from the points in the pic im sure the other point is GND any help is greatly apreciated mate i have another board here and them points are not shorted so im thinking somethgin has gone somewhere. the drive picks up in JF and i get status 72 and chip/drive properties just fine. just get the 7777777777777777 grrrrr thanks dave Do you have the original fw (or the one that has correct dvd key)? If not, try to press CTRL+F12 on Jungleflasher, it should open a list of dvd keys. If that is empty too, try to check the JF log. The reason (most likely) why the dvd key is 777777777777... is because you didn't copy the original dvd key to lt+. hi mate the key is this when i read the drive in im not sur eif i have the orig dump as i have hundreds of dumps on my pc lol. also does the ctrl + f12 carry over to when you change jungle flasher ? also when i id the drive in JF wouldnt it detect teh drive serial and tell me it has the key on file ? thanks dave |
|
|
|
|
Logged
|
|
|
|
frazzeld
Newbie
Posts: 6
|
|
« Reply #1005 on: January 03, 2011, 04:03:20 PM » |
|
Dave...but your drive is showing all 7's! so more than likley the key wont show up.......have you attempted the find key in database (right click on key)
|
|
|
|
|
Logged
|
|
|
|
|
dave11674
|
|
« Reply #1006 on: January 04, 2011, 09:40:08 AM » |
|
yeah
its the last one in teh jf log
so i presume its the only entry for this drive
i also tried searching bar code and serial numbers in the log
but to no avail
the drive is fluffed
he can have it back
i have noticed the MT chip is getting hot too
dave
|
|
|
|
|
Logged
|
|
|
|
Aids76
Newbie
Posts: 2
|
|
« Reply #1007 on: January 09, 2011, 12:03:18 PM » |
|
Hi guys ! My problem. Liteon dvd not detected in jf and dosflasher. I assumed its something with the board on liteon. The problem is i was trying to flash the drive,but i couldnt even get to the jf,beacuse of short circuit. Now my Ck3 lite is screwed and the dvd rom too. And im without key for new dvd. I tried this repair but still no luck. Still not detected in jf. Pushed the key on the switch and leave it on for about 10 sec,nothing. Please if anybody had any suggestion i would be really happy. All i want is the key of my dvd rom. Here are the pics. Soldering is done by my friend who knows how to solder. Help me,please ! http://s1209.photobucket.com/albums/cc397/aids76/ |
|
|
|
|
Logged
|
|
|
|
|
LordX
|
|
« Reply #1008 on: January 12, 2011, 04:45:36 PM » |
|
3,3V to GND Resistances.
30 - 400 ohms maybe burned pin 122 tx/rx.
drive have 351 ohms @ 3,3V to GND , all tracks are fixed , soldering is perfect good. ( drive chipset is hot , drive have no response ). any tips to fix it ? burned pin 122 ? |
|
|
|
|
Logged
|
|
|
|
|
phantitox
|
|
« Reply #1009 on: January 13, 2011, 03:37:45 AM » |
|
one question, i have a 9xxx unit, i lost the 101 pad, i check this thread and try to fix it from the cb24 , but well i blow the cb24 and cb37 cond.  i dont need to dump the firm, i just need that the unit work again i have some spare pcb from lites 7xxx but those smd well i dont think that i can solder those back, im scare of connect the unit to power cauz i dont know if without those cond. the chip will fry or something i just need some direction of what can i do , excuse my english im spanish. Thx ahead. |
|
|
|
|
Logged
|
|
|
|
|
albon
|
|
« Reply #1010 on: January 13, 2011, 02:33:21 PM » |
|
Why dont you the pcb with one of your liteon 7? Then flash it with your firmware.
|
|
|
|
|
Logged
|
|
|
|
|
phantitox
|
|
« Reply #1011 on: January 13, 2011, 08:46:59 PM » |
|
Why dont you the pcb with one of your liteon 7? Then flash it with your firmware.
cauz i could dump the firmware, im trying to restore this unit leaving it stock i dont wanna mess around anymore with her. i just need to know if i can leave the board without those two resis. cb37 and cb24 i dont wanna turn it on cauz im afraid of fry the chip and loose the console  |
|
|
|
|
Logged
|
|
|
|
|
treal420
|
|
« Reply #1012 on: January 13, 2011, 11:52:37 PM » |
|
Ok,so this is what i received from a friend after he tried to fix it.All i want to do is dump it an put in a new drive.What would be the easiest way to fix an dump this drive?I tried to get better pics but this is all i have,red X,s are lifted pads.Any help would be appreciated. http://img810.imageshack.us/img810/1041/dsc02740t.jpg |
|
|
|
|
Logged
|
|
|
|
|
phantitox
|
|
« Reply #1013 on: January 14, 2011, 01:48:49 AM » |
|
Why dont you the pcb with one of your liteon 7? Then flash it with your firmware.
cauz i could dump the firmware, im trying to restore this unit leaving it stock i dont wanna mess around anymore with her. i just need to know if i can leave the board without those two resis. cb37 and cb24 i dont wanna turn it on cauz im afraid of fry the chip and loose the console nevermind i just solved it , it seems those resis well they dont do anything while ur using the dvd unit, i mean there are not essentials in the unit i test it around 3 hours now and seems ok. |
|
|
|
|
Logged
|
|
|
|
Milker
Newbie
Posts: 4
|
|
« Reply #1014 on: January 14, 2011, 07:29:30 PM » |
|
Hey fellas!
I cut the MRA traces and then accidentally reversed the power which blew R207 and R204.
After reversing the cut traces, jumping R207 & R204 and adding 3 volts to C03 I have some power again.
If I turn on the xbox with the drive open it closes and the motor continues to try to spin and gets hot due to resistance.
I have checked all voltages and they seem to be within tolerance... Any ideas?
Thanks for any help in advance.
|
|
|
|
|
Logged
|
|
|
|
sd-253
Newbie
Posts: 8
|
|
« Reply #1015 on: January 14, 2011, 07:40:55 PM » |
|
Hi
Please if you know the spec. for the LO 9xxxxx pcb bord ME 1117 voltage regulator , would you let me know
Thanks
|
|
|
|
|
Logged
|
|
|
|
gwrace
Newbie
Posts: 1
|
|
« Reply #1016 on: January 15, 2011, 02:29:01 AM » |
|
Ok brand new to this forum. I purchased two new Xbox Jasper Elite consoles and decided to try modding one of the new Liteon 9 series drives. To make a long story short I purchased LT 1.5 switches, CK3Pro and CK3Pro Probe II. I made the mistake of trying the LT Switch first and managed to lift a few pads in the process. I've not had any issues in updating firmware on the Benq drives I keep around as spares, but I would like to retrieve /dump the firmware on this drive to make that switch out possible. The drive was recognized in bios and in Jungle Flasher prior to the dvd board modifications. I've spent the last two days reading this site and trying various wire work around solutions and I've gotten nowhere. I would appreciate some assistance. I'd like opinions on if the board or drive key can be salvaged. Much appreciate any assistance. See the link for pictures of the botched board. http://entertainment.webshots.com/album/579530229jKLtdI |
|
|
|
|
Logged
|
|
|
|
junito91
Newbie
Posts: 1
|
|
« Reply #1017 on: January 21, 2011, 08:31:39 AM » |
|
i need help!! plz
ok first i did the vampire with rebuild board, i did it like in 10 min very easy following instructions, everything went fine, read, good key and flash, i press outro ata and put it together, connect back to pc and jungle flasher detect the drive good so far, i left the drive on my desk to put the xbox together in the morning, when i put it together the power light of the xbox stay flashing all the time like i was trying to eject, i turn it off and on and the same, so i went back to the pc with the drive and jungle flasher, and the drive does not eject, im like wtf so i keep playing around, and found that if i put the vampire on pad 101 on the rebuild board the drives eject and does get detected by JF, if i dont touch the pad doesnt do anything, any advice , any help?
|
|
|
|
|
Logged
|
|
|
|
Shadowlance8
Newbie
Posts: 3
|
|
« Reply #1018 on: January 24, 2011, 01:35:34 AM » |
|
So ive been reading through here for the past couple days trying to find some tips and answers. I have found lots of great stuff but I have an issue I can't seem to fix any maybe you all can guide me a little. I have a virgin lite on 9345, flashed it by way of mra, put it back together and got 3 rings. I rechecked my traces and now there is no red ring. What I have now is the flashing green eject light. I have checked my connections for continuity and they seem fine, when I check the 2 points listed above with my meter set at 2M I get nothing. Could this just be a case of a bad flash or have I fried my chip? I don't think I need to have the drive powered to check the resistance but maybe a possibility. The only one I haven't tried is putting a jumper in and cutting a trace and checking the resistance as stated a few pages back. I've read that it may be a short somewhere but I've put my tester on the connections and the ground spot and got nothing so I'm at a loss. If you guys have any suggestions or tips I would really appreciate it. I can put up pics of the board and an edited version of the JF log if that would help. And I have already flashed the drive successfully according to JF. Thanks
|
|
|
|
|
Logged
|
|
|
|
|
Pacote-san
|
|
« Reply #1019 on: January 26, 2011, 11:03:44 AM » |
|
The key from this drive was already dumped so just wanna know if theres a way to make it work again When turned it on , smoke can from the lines and they burned.... opened and discovered that the solder drom 3.3v was touching the ground   Where can i connect to bridge those burned points? |
|
|
|
|
Logged
|
|
|
|
|
Dilber MC Theme by HarzeM