|
maximilian0017
|
 |
« Reply #460 on: January 03, 2010, 05:24:23 PM » |
|
So i am using a usb spi that grim 187 made but i cant figure out whats wrong ive patched the xbr file and everything when i load nandpro to flash it wont. when the usb is plugged into the pc it says found new hardware then it says there was a problem or malfunction and then i went to the driver and it says unknown driver. i tryed pointing it to the config.inf for the driver but gives an error... im running windows vista 32bit and ive installed the port95 tryed both with compatiablity mode and without. Also I tryed it on my 64bit win7 labtop and its a no go. But since its home cannot do the xp emulator and I am stuck waiting for my lady to bring her xp labtop. Any ideas to why it isnt working. I also tryed turning off driver liscening on vista.  Im so confused. Also if your wondering how I have the orignal bin for kv and nand config ect it was provided. I belive grim used the spi and it worked for him fine. Most common problems: 1. The processor isn't running correctly/ at all , check powerlines, crystal etc 2. The usb isn't connected propperly check D+ D- (wrong way around?) 3. You didn't program the bootloader correctly, check selected frequency etc |
|
|
|
|
Logged
|
|
|
|
vSaAmTp
Newbie
Posts: 7
|
|
« Reply #461 on: January 04, 2010, 08:08:44 AM » |
|
Thanks Arakon U mean this One? Thanks for help... |
|
|
|
« Last Edit: January 04, 2010, 08:38:41 AM by vSaAmTp »
|
Logged
|
|
|
|
|
dak
|
|
« Reply #462 on: January 04, 2010, 08:27:33 AM » |
|
...when the usb is plugged into the pc it says found new hardware then it says there was a problem or malfunction and then i went to the driver and it says unknown driver. i tryed pointing it to the config.inf for the driver but gives an error...
had the same prob 2 times: 1) forgot 5v at pin 13 2) short between 13 and 14 check your wires Edit: 1) this flasher worked at my laptop correctly, but not at my desktop |
|
|
|
« Last Edit: January 04, 2010, 08:31:51 AM by dak »
|
Logged
|
|
|
|
|
m60_maniac
|
|
« Reply #463 on: January 04, 2010, 08:33:08 AM » |
|
is there a nood friendly tutorial for making one of these? im using an lpt cable atm and it takes far to long to dump and write ect.
|
|
|
|
|
Logged
|
|
|
|
|
dak
|
|
« Reply #464 on: January 04, 2010, 08:52:14 AM » |
|
is there a nood friendly tutorial for making one of these? im using an lpt cable atm and it takes far to long to dump and write ect.
Did you read this tread before posting ? |
|
|
|
|
Logged
|
|
|
|
|
m60_maniac
|
|
« Reply #465 on: January 04, 2010, 09:30:03 AM » |
|
yea i read the 1st few pages, didnt realy understand how to make it from the 1st post
didnt have time to read all 24 pages
|
|
|
|
|
Logged
|
|
|
|
|
maximilian0017
|
|
« Reply #466 on: January 04, 2010, 02:13:29 PM » |
|
yea i read the 1st few pages, didnt realy understand how to make it from the 1st post
didnt have time to read all 24 pages
You will probably be better of buying a ready made one. (probably the same price than if you bought all the tools and materials) |
|
|
|
|
Logged
|
|
|
|
|
m60_maniac
|
|
« Reply #467 on: January 04, 2010, 02:58:02 PM » |
|
no one in the UK sells them, only seen grim selling them. if i can make then i was thinking of making a few and selling them on to people
|
|
|
|
|
Logged
|
|
|
|
|
joeyddr
|
|
« Reply #468 on: January 04, 2010, 03:39:09 PM » |
|
yea i read the 1st few pages, didnt realy understand how to make it from the 1st post
didnt have time to read all 24 pages
You will probably be better of buying a ready made one. (probably the same price than if you bought all the tools and materials) Where's all the fun and learning in that  |
|
|
|
|
Logged
|
|
|
|
|
m60_maniac
|
|
« Reply #469 on: January 04, 2010, 05:09:53 PM » |
|
exactly  so if anyone could make/knows of a good noob friendly titorial of how to make it and what to buy then i would be greatful |
|
|
|
|
Logged
|
|
|
|
vSaAmTp
Newbie
Posts: 7
|
 |
« Reply #470 on: January 04, 2010, 05:59:59 PM » |
|
So i think the Part-List for Reichelt.de was so ok... List for the first post in this Thread: Reichelt Part List for the Flasher (Kon) Reichelt Part List for the Flasher (SMD) Reichelt Part List for the Programmer When something is wrong, tell me and i change the Partlist. Danke... |
|
|
|
« Last Edit: January 05, 2010, 06:32:44 AM by vSaAmTp »
|
Logged
|
|
|
|
|
porchmonkey
|
|
« Reply #471 on: January 04, 2010, 06:58:03 PM » |
|
|
|
|
|
|
Logged
|
Xbox 1.0 // cromwell 2.40 // fedora core 4
Xbox 1.3 // SmartXX v3 // xbmc
Xbox 360 Elite // jtag // freeboot 0.032
|
|
|
|
m60_maniac
|
|
« Reply #472 on: January 04, 2010, 07:14:11 PM » |
|
dak your not particualy helpful are you would have had time but ive been out, i checked the site on my phone so wouldnt have been able to read them all. and yea i will read them all when i have the chance |
|
|
|
|
Logged
|
|
|
|
|
|
|
d4m4n
|
|
« Reply #474 on: January 05, 2010, 02:01:36 AM » |
|
Using the wiggler clone JTAG to program the PIC is no better than using a simple programmer like ART2003. You need to get a device for programming in both cases. |
|
|
|
|
Logged
|
|
|
|
|
doveman
|
|
« Reply #475 on: January 05, 2010, 07:19:46 AM » |
|
True, but I was just thinking of being a bit lazy and only having to build one thing, as I can buy a wiggler clone for only a few quid more than the parts to build the programmer.
|
|
|
|
|
Logged
|
|
|
|
|
dak
|
|
« Reply #476 on: January 05, 2010, 08:34:58 AM » |
|
Reichelt Part List for the Flasher (Kon) When something is wrong, tell me and i change the Partlist. The usb plug is B and the wire is A, doesnt fit. Only 5x 100 ohm is needed. I used Kerko 33pF 500V, no idea if yours work. |
|
|
|
« Last Edit: January 05, 2010, 08:38:01 AM by dak »
|
Logged
|
|
|
|
|
Arakon
|
|
« Reply #477 on: January 05, 2010, 09:56:08 AM » |
|
500v is total overkill, considering there's only 3.3v flowing at most.
|
|
|
|
|
Logged
|
I do NOT give support by email, PM, ICQ or whatever. Anyone annoying me that way will have his balls removed. With a rusty butterknife. Slowly. And I'll enjoy doing it.
|
|
|
|
mosses
|
|
« Reply #478 on: January 05, 2010, 02:31:10 PM » |
|
i used this tut http://docs.google.com/Doc?docid=0AXkkEcX2mtTjZHg5cGc0dF80Y3RkcmhqZjM&hl=en and m successfully able to get to the memory access part..  but when using nandpro to read the nand of my xenon i get this error immediately "Looking for usb interface device Could not detect a flash controller! Can not continue" i m stuck pls help |
|
|
|
« Last Edit: January 05, 2010, 02:33:05 PM by mosses »
|
Logged
|
|
|
|
|
maximilian0017
|
|
« Reply #479 on: January 05, 2010, 02:37:47 PM » |
|
Where is your orange wire going to?
|
|
|
|
|
Logged
|
|
|
|
|
Dilber MC Theme by HarzeM