Check out my first slim Star Trek Casemod!

http://www.youtube.com/watch?v=dsbeRh63imo

I've seen adapters made from old phat 360 ROLs to use the controller on PC. does anyone know the pinout to use a slim ROL. I have a spare one and figure it would be better because the sync button is located on the slim ROL.

Here is the goal. I want to switch NANDs, reset the SMC, and power on/off the glitch chip with one switch.

I had a hard time reading this:

Thanks d4m4n for the schematic.

I came up with this schematic using a 3PDT switch:


Do you guys/gals think this will work?

EDIT: I edited the schematic with proper orientation and used the actual nfet symbol to make it easier to read.

I am getting 3.3v on all points on the board and Cygnos. It wasn't on WP, but now have it corrected. I am still having issues. It will not allow me to change settings or auto sign in with any profiles.

If I am not getting a connection, is there any alternative points to solder to for both WE and WP, and if so, where are they?

I'll check the WE. I didn't seem to have any problems with that one. I lifted the pad on WP but It seems with enough flux I got it soldered on. Do you think the WP may have something to do with it? Would that also prevent me from connecting to my PC for streaming media?

I semi-successfully glitched my slim and installed a Cygnos and relay. Here's my problem. When I have the Cygnos on, it will not allow me to save changes such as Kinect data, auto sign in data, and saftey settings (to block XBL). The normal  NAND does not act in this fashion. The only way around it is to create the settings in the normal NAND, dump it, and rebuild a ggboot image. Anybody know where my problem may be? It's a bit of a pain in the arse to have to do, and I also do not know if it will have any other adverse affects.

I'm in almost the same situation (360 missing DVD key from FW 8xxx+). I am interested in finding a workaround. I have an idea, but am running it buy you guys to get a second (or third, forth, fifth, ect.) opinion. Here's the basic rundown of what I had in mind:

Things needed:
360 with missing DVD key
Way to read write to NAND (LPT cable, NANDX, ect.)
NANDpro
7371 Donor NAND the same mobo version (Xenon, Falcon, ect.)
Xell
Jtagged 360 with the same mobo version
360 Flash Tool
Jungleflasher

1. Use your preferred method to dump NAND from 360 with missing DVD key.
2. Use NANDpro to extract the KV and config from NAND with missing DVD key.
3. Use NANDpro to inject the KV and config into the 7371 donor NAND.
4. Use preferred method to make backup of Jtag's NAND to flash back when done.
5. Use preferred method to flash donor to Jtagged 360.
6. Use preferred method to flash Xell to Jtagged 360.
7. Run Xell on Jtagged 360 to get CPU key.
8. Use CPU key with 360 Flash Tool to open NAND from 360 with missing DVD key and get DVD key.
9. Flash backup of Jtag's NAND back to Jtag.
10. Use Jungleflasher to flash fimware with correct DVD key to the DVD drive of the 360 missing the DVD key.

Do you guys think it may work? Is my theory sound?

I was thinking about something more like this:

Let me start over. I need some help designing that circuit so I can use it in a case mod. If someone can point me in the right direction or has a schematic I can use, it would be greatly appreciated. I can find videos on how to get them to alternate, however none of them explain how to time the lights. Can anybody help?

Sorry if this is in the wrong topic. Moderators please move topic if nessesary.

Hey guys I want to make a small circuit that will power 2 led strips alternating every 30 seconds.