no them 2 wires with the diodes and 1 jumper is the jtag trick(used after you flash XBR over to the nand).
lets just say it validates the new dash to run..amongst other things...
you need to worry about the LPT(printer port ) wiring setup to detect the nand....(7 wires.5 resistors and 1 diode)
remember on the connectors (on pc and cable) show where pin 1 is...so make sure that's matches up.....

we have a whole posting for this alt point....
search......
also i wouldn't even worry about this jtag spots...till you fix your lpt way to read this consoles nand...that's more important...

and you do know if it's a Zephyr then use the XBR_3a for falcon...
quit robbing peeps pics to..lol

GOOD DEAL....SLEEP MAN SLEEP

just wanted to give a heads up for the 360 re-balling + site
it's back up and running so any member(s) that i am working on there stuff...please sign up there and give me a shout in the welcome part ..so we can keep tabs...
thanks,
RE
360Reball

there no + or - for it......silly...you'll be fine...same with the caps for it...

Anyone use this XeXMenu1.1 and have it halfass work sometimes and then other times it just loads up a blank screen and you have to turn the 360 off and on again


weird as no one else has a problem with this....I know i don't.....
maybe it's the console itself ...or the user...lol

what is day and night ..i got lost about it.......lol
sleep......where...bear in a winter cave........<confusing??? I am...lol
and yes the body needs 7 hours sleep...- 1 hour for waking up here and there...
you will find out as you get older you will need at the least 5-6 to keep in balance...


morenomdz , you get it up and running?

it's all right here...see where 9 and 10 pins are....
http://www.xboxhacker.org/index.php?topic=12306.msg101565#msg101565

what are you trying to do I thought you said you programed the PIC chip already....
you lost me now...lol

ISCP port but I dunno what I'm connecting up
see where the white lines in my pic are that's the ISCP hookup
what Willem are you running(this is important-for the program that runs with Willem) ...
that pic is my Willem 50E....with PCB50_98D10 software...
and in the device list it should be shown as ,
PIC18F2455/2550/4455/4550 ...which ever PIC chip your going to be running....

wouldn't you say it's hard to write a file of (File: 3de) only

in case the op didn't know ...that ain't obvious is it...

WILLEM 50E


Can't get any easier then this...lol

yep and convert that to decimal....

yep and you can also use winpic800 to set the crystal too.......then willem to flash it  over...

pin 4 is tray status
pin 6 is 3.3 volts


pin 5 is ground...for reference....

what diodes are you using?
did you try to flash the drive back to stock and check it(worth a try).

VGA Sync if needed

VGA -------- x360
14(VSYNC)   -12(sync(VGA Mode))
10(VSYNC-)  -10(sync-)

try this....

VGA -------- 360
1(red)         -3(red)    
6(red -)       -1(red -)
2(green)      -4(green)
7(green)      -2(green-)
3(blue)        -8(blue)
8(blue-)       -6(blue-)

the vga readout is from the newer 15-pin VGA pinouts

cypher21
can you change your topic to questions for the alt route for liteons?

this way it can be in with this post..showing a solution......
http://www.xboxhacker.org/index.php?topic=14040.0

and all questions can be asked here about there to...
I am just asking so we can kill some clutter up about the diagrams....
and thanks once again dream for creating solutions for the problem children with there solder kits...lol

P.S  maybe we can get a admin to split this topic too, along with my post......