Serial flash found with Status 0x72

Sending Device ID request to port 0xBC00

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name:  MXIC(MX25L2005)

Flash Size:  262144 bytes


right there it is ready to read and write(flash) Status 0x72....so i would say a different value,
buy your disconnect/reset  error of (Sending Vendor Outro to port 0xBC00)

and a search would of helped...there is a whole section on this ...

can you hear the ball moving?
not saying 2 drives checked could be both bad belts but who knows...
but as he stated he checked with a different drive....

and by tilting the unit up and getting a 100% error each try,we know it has to do with the switching (tilt censor) because of the drives laying flat and not working when the unit was tilted..

here you go....don't mind the dust on the board...it's a parts board...




when tested with a multimeter setting on 300mw and diode check and any + or - on any of the 4 pins..
with the board laying down shows (no measurement).
standing up there is a measurement of 002 on all 4 pins...

good deal glad you got it going...and yes sorry typo on the falcon....it's a working Xenon now

write only the system backup of 66mb and check the diodes to...
and you know not to use the mu part...see what happens when you mess around....we warned ya ,right!
it posted at large...

can you pm me and send me a nand copy?
I will look at this....
you might have to just flash free60 falcon to the nand and nothing else and then reboot the unit to xell...

first did you read through this section ...liteon fix
your not the first with the problem... and make sure you post in the right topics...

cant jtag dump first part of nand been patched???
what ever that means?

you mean the dash is 8XX or higher?

remember if you havew a 256 or 512 jasper messing with the built in memory can cause this to after days....

you wrote,
I changed my resistor from 1N4148 to BAT41 also.


correction ,there called diodes...

does the orig nand work?

good idea then you can boot to a e79 error when will make you do other tests......

inject the falcon free60 xell inject xellous then reinject your kv...then power down and reboot using eject..or just pm me for a place to grab your nand and i will do this for you if you run into problems...
also,make sure you have a good nand copy to...


also can you snap a clear pic of your wired up jtag?

i don't know
what i was thinking that bincrypt don't give leeway for messed up bit's like flashtool does for 1 bit wrong....
and relient_k where did you go? last we talked you were going to check out the ECC checking?

and last nand you check from me...you booted and got E79?
which means a bad connection (diodes )
corrupted kv
or wrong kv for that mobo.....

don't you think if it can be done it be posted all over the net?
NO...
and wrong way to first post....read the rules before you post...this isn't your kiddie forums you just pop in and post at

where is the part close to can you pinpoint it....

Grandmaster as modguru stated,
uninstall the via drivers are they are the problem making the pc lock on erase command(same with liteon)
everything else will be normal but the erase .......

or use dosflash with modeb for benq...

what are you using to flash with?

could be a fluke that ,that block went bad...(some do).
did you just load your dump up in flashtool and check the cpu key?
also your injecting a encrypted kv back using nandpro right?
nandpro orig.bin: -r16 rawkv.bin 1 1
nandpro orig.bin: -w16 rawkv.bin 1 1 (can be orig or xbr)

encrypted only..
and if it shows error on that block ,you have to remap it....

yes or i just do it through the pc.....thank god not alot as it takes forever...lol
but for the dlc 16gb stick can handle alot of them files....as for games(iso's) well 2 at a time..

can it even be jtagged ? whats the CB and dash version?
check your wiring...are the diodes right? did you check to make sure the connections are intact?
did the nand have any errors on the copys? when you read it?
did you inject kv and config right?
did you install xellous or xell to get your key by using eject...

bestpig tool was corrupting for a bit as posted somewhere around here ....don't use it...
use jtag 1.7 works great for making freeboot all you need is a clean copy of your nand to do this....
or just do it with ibuild...
any problems pm me.......
Zephyrs are kinda of screwed up with any rebooter for now but work when on...

swaping the same cpu and same nand at the same time works...