just flash your console with LT3 and complete the update and you will be fine .

some times is ldv isues  if you have your cpu key add +1 the ldv in a new image and flash your console with that and maybe it is ok

use a multimeter and check for continue in your wiring

the solution for this problem is your ldv  everyone of you have tis issues after the update . it is lucky  i do not thing so ..
if you have your cpu key just add +1 in your ldv with flash tool and with this image build your xell .  i have the same problem and this is the solution . check your ldv noy if it is 6 put your cpu key and pach it make it 7  and with the new ldv image make the ecc.

the nand for a fat fits perfect if you have the skils to change it give it a try . but only if you have the skils  in another case senario you will end up with a destoyed console .

yes find another nand  desolder yours and solder the new one  i have 2 jasper bb 256 and 512 with that problems . after i have change the nand the console boots fine

check the secondary error if it is 0022 maybe it is your ldv . i have this problem once in my dual nand console  . and i have add +1 the ldv and everything works perfect

do you have a good dump ? if they write in back the console boots normaly in dash ?

hello  everyone
i will write this maybe someone elese has the same problem and have find a solution .
as i have read so far and i have read alot in all the forums tx , scene , here , the do not exist something standar for this console 512 bb 6751 cb
everyone has his issues and in every case is diferend senario 680p, 50n 100n 68n diferent sollutions every time .
here is mine situation and is my first time something like that hapend .
i have dump 512 nand and 3 times for 64 mb  i have a perfect dump and i use multibuilder to create ecc . the message for the bad cb comes up and i know that multibuilder use donor cb to make the ecc so i have continue . i have write the image and i have try and with nandpro2 and with nandpro 3 ( i have 2 olimex pcb ). i use my one  custom pcb for all the consoles . (it is not the chip the chip in other console works perfect) . and wen i power on the console the green led blinks and the fans every 4- 5 sec make reset it works normaly . the problem is that the console never boot to xel and after 30 sec the fans starts to grow they speed and after a minute a minute and half  they works 100% speed . the console it is not hot at all . and this is the final stage of the console a consoleplane ready to flight . and no xell .. if anyone can helps with that i will be very hapy ...
ps i thing that will be very nice if someone has another problem with his 512 bb console to write the problem  and his solution to one thread . or here to start helps other people ...  please just write the problem and the solution you will help alot .

TRY WITH  360FW-Toolbox-48 it is an old program from maximus  maybe they can still do the job

make the console RGH  (reset glitch hack)  and  you do not even need this drive again .. or restore the key with RGH  and buy a new drive .

hello
i have go to the stores today and i have buy one new slim console with 250Gb hdd
i must to see now that i have flash over the 50 slim in any version camicazi or not unlock
and wen i have open the console i see that the drive was 9504 .
wen i have plug the drive to my pc i see that was 0225 recognized by the jungleflasher .
ok i have read and store the key dummy serial info and everything ok  .
it was winbond  and i have make the camikaze hack everything gone perfect , i put the lt 2.0 0225u firmware as target .
spoof and i have write seccesfuly the target . ok i  plug the drive back to console and i have go to check it .
here i must write that before check the console i plug a usb stick with the 13604 update and i made the update first ...
after the end of update try to play games and nothings hapend just play game in XGD3   and play dvd in xgd2 and older .
i try with original games and only play dvd came up in the screen ..
here i must say that i have try the multi outro ventor  try
and i have flash and  try and with another pcb just in case .... 
after that i thing something mismach with the drive key and i made it glitch to see the dvd key ...
the dvdkey comes same on the tv screen as the jungle shows . now i am sure about the key . the key is correct .
i have flashed over 1000 times and first time i have see something like this .. my only thoght was that something hapend with the
serial of the job .. like i must made first update the dashboard . and after to flash the drive and not the oposite .
i do not have something elese in my mind . if anyone has any thoghts and can help

that will be very nice . thanks alot .

no m8 you can fix the drive with only the dvd key ...
if you can send me all of your data i can give it a try to build from you your firmware .

hello i have a jasper console red  and i have make the update 13146 but something has go wrong . before complete the update bar to 100% the shows me a black screen with the error E81 .
i have try all the other update that exist 13599 13604 but every time hapend this before complete the update bar E81 screen
so i have deside to take the cpu key and to extract as many data i can from the nand dump .. in the kernel extraction this message shows up

as i can understand something has gone wrong with the update and the 13146 kernel it is corrupted .
now i am wonder if they exist some way to fix that console ...
any ideas is welcome ...

if it is possible to change it yes i have

it is possible to see this info?  or am i missing something here ?

is this for sell or is to share your work ?

play original and not backups means that you have not flashed with the ltplus 1.91 firmware try again ..
and what dasboard you have right now ?

can you posts some photos of your jungle flasher .. maybe that helps

yes you must write your drive with the ltplus025v1.91  firmware to woks and do the latest update ..
be carefull not with the 0225 this is another firmware .. the firmware you need is 02510 

first of all solder again the pin in his plase .
second do not make mra hack
use the pmt hack it is more simple ...
find the jungle flasher user guide  and folow the steps for pmt hack ... and you will ok
if and this not help take your dvd key with the RESET GLITCH HACK ..  god bless gligli for that ..  from your console