so what the hell is wrong with this mb??!!
im loosing it!! regular spi dosent work and it dosent boot its really f***ed up!

is here any chanse that it could be an ldv mismatch?
cuz client wasnt reall clear
he sent xbox by mail cuz he lives far away...
could it be that he updated to a higher dashboard without making a new nanddump?
could it cause the xbox to continue flashing green with no response?

ok installed cygnos programed with original nand and still the same blinking grenn light...
any chanse it is related to the resistor conecting to cpu_pll bypass?
cuz it dosent look to good
any other ideas?

got a clients 360 here that can detect flash controller
soldering is perfectly fine this is aprox my 60th rgh
but problem is that he tried to rgh it and failed! spi use to work-he got perfect dumps
but now cant read or write....
fixed his standby clk....
and console boots. wel not exactly but green flashing light
no dashboard!!
most likely since he tried to writeoriginal nand back after xell! since then it stopped working
any suggestions?

so how do you explain that with the same setup(solder work was not touched)
tried multibuilder 0.7 3 times! no boot
and with 0.3 first boot

no nedd for a pic
sinced i used multibuilder 0.3 instead of multibuilder 0.7
and instant boot!!
so yes soldering was perfect not my firs glitch belive me

no bad blocks?
so what alternate points ahould i try?

i have done until today sprox 35 consoles
all glitched fine
but today i came across a slim that just wont glitch!!! redone soldering 3 times changed 2 coolrunners to make sure
played with cable length tried everything!!!!!!!
my soldering is fine i promise done to may jtags and RGH and soldering is PERFECT
so my question is are there any suggestions???

many consoles i have modded have the same issue

but he says his system is already glitched!! and he has the original nand dump that was used in order to glitch
so all he needs to do is use that nand dump his cpukey and the new multibuilder to build a 14999 glitched dash!!
thats it!!
LDV didnt change since he didnt update!!

you can use your original nandump it dosent matter since LDV did NOT change

by the way are you from ISR?

absolutly not!!!!!!!!!!!
build new image using multibuilder 0.7
and flash to nand using flash 360 or raw flash v4
the apply $$ystemupdate

scrape the trace and solder to the second end of the resistor(the hana side)
it worked for me( repaired two systems that way)

im having the same issues
boots one to 20 boots or even more
jasper cb 6750

just an off topic question
what hardware did you use in order to glitch?
cuz i used a matrix with a 330PF cap that was able to glitch only 3 minutes after turning on
now resolderd everything and now it wont glitch anymore
any suggestions?

im telling you both jaspers were fine before rgh
heatsinks were cold temps were normal
after rgh temps go very high only on gpu!!
on three consoles(trinity cpu aswell but im guessing its because proximity to cpu)
so so,ething is clearly wrong
i used ggbuild 0.33b by rogero
to create nands
and i use matrix glitcher
ca it be the matrix glitcher overvoltging something?
giving it to much juice that will cause a chain reaction that will lead to gpu overheating?

ok but has anyone had the same problem?

no i firs noticed when i touched the gpu heatsink that was damm hot while cpu heatsinks was almost cold
and this happend on 2 different consoles
so i dont know what it is....
any help? can anyone check his own jaspre and report temps?
my japsers gpu's go to 75 C within 5 minutes or even less when fan i ste to auto
so i put it on 100 and temps drop to 50C

well till today i have done 3 consoles using matrix glitcher: 2 jaspers and one trinity all booting ggbuild fine...
the thing is that i noticed that in all consoles
gpu tempertures are rising very fast and even get to 75 C
so i set all consoles fan speed to 100% in order to avoid overheating problems
can anyone confirm this?
is it a bug with the glitch or ggbuild?
or maybe my matrix glitcher is causing this somehow?

thanks in advance...

i got a lost dvdkey jasper that i retrived its key using rgh
after writing back to stock i felt that while operating gpu got insanly hot
and for some reason everytime i wanted to update the dashboard it wouldnt let me-just go black screen and freeze
so i decided to rgh the machine and load ggbuild on it
after i finished gpu is still insanly hot and in xexmenu i can see temps at 70!! and rising
so now i need to figure out whats the problem
any help?
maybe something wrong with config?
by the way cpu tems are normal and even cold
oh and one last thing while running xell gpu does not get hot