me neither. 0022 is probably smc related.

really need to get the key off this board. however, the board will NOT glitch. no matter how long i let it sit.
spent several hours today trying to get the board to glitch with no success. turned right around and pulled the key off another 4578 zephyr that glitched almost instantly.

i know that zephyrs are very finicky but i really dont want to trash a working board just because i cant get the key.
i have tried caps on both cpu_rst and pll_bypass.

are there any tricks left to possibly get this board to glitch just 1 time? thats all i need, 1 time. 

sorry to bump such an old topic. but this post is 100% correct. got a jasper that booted to dashboard but had 0101. someone had attempted to 12v fan mod, remove wire/solder and console booted/green light.

ok, i got this board to repair. the console would immediately power on and then off or on and turn the fans on high speed after plugging in the power.
i removed the smc and replaced it with another from another board. that fixed the crazy power problem so obviously the smc was damaged.
now the console will only ding when the power button is pressed.
it is a failed rgh attempt. not quite sure what the owner did to damage the smc.
i removed and replaced the hana with another. after this the console powered on ok. i thought it was fixed. but after letting the board sit a while it would not power on anymore.
i reflowed the hana i had just replaced and same symptoms. console powers on but after sitting it will not power on.
it seems the heat from reflowing causes the board to be able to power.

i dont want to junk the board because its obvious it can be repaired since it powers immediately after reflowing but not once it cools completely.

i have no idea what to check from here. anyone have any ideas?

i dont have the rol wire hooked up though. but ok. thanks.

if your original nand was ldv and you updated the ldv is now 4. try patching your nand backup to ldv 4 and reflashing.

someone else has the same problem though:


im just going to take it all out and put a hardware switch back and wire it up manually. at least that worked 100% of the time. lol. and how is it to flip a switch. this switching code seems too buggy.

i have a problem with this code as well. the console switches nands ok but ive only gotten it to glitch and boot successfully once. each other time it red lights. sometimes after 6 seconds, sometimes after 15-20. it seems that whenever it would start to actually glitch and boot is when it red lights. the fans will speed up, it will make the real fast glitch sound like the ft4r2 wire is damaged but its not. any ideas? stock nand boots perfect 100% of the time.

99.9% chance the laser in your new drive is crap. thats why the disc spins for a second then quits.
so either replace the laser or tell the people you bought the drive from its crap.

laser in your new drive is crap. need pot tweak (might work) or a replacement laser (better).

can you help me with my problem perhaps? will your diode fix work? http://www.xboxhacker.org/index.php?topic=17831.0
console is on stock 13604 dashboard and 14699 ggbuild.
does the mod just not work with matrix boards?

i tested it on an 0272 drive and it worked. console played a game fine.

can you read? he asked about mt1335we, not 1399e. 1335we can be used of course if it is the unlocked version.

sure am glad we cleared that up.

this is the 2nd and 3rd time ive gotten one of these boards. they are most definitely hand soldered (the ic and spi at least).
they are also designed so that the spi is where the temp sensor would normally go.
does anyone have any idea who/what made these boards?

i buy from a different seller on ali. no problems though.

why trash? replace mt chip.

did you look at the tag on the laser? hop141d

tested a rol yesterday, console didnt power and the chip above the ribbon connector got REALLY hot.
found this post today, removed both caps above the chip and the rol worked again. put the small cap back on the board and replaced the larger cap. c58 and c57.

ive got a chassis with tray and metal housing. i robbed the spindle and worm motors from it, pcb too obviously.